Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 12, 2019 22:28:41 GMT
Couldn’t you just stick them on an open baffle? You could, but there's no predicting the results. Plus decent ones would need to be pretty large.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 12, 2019 22:31:20 GMT
You know geoff, it could be a lot of fun. I like the look of the drivers and they seem to have a decent cabinet drawing to go with it. I'll have a chat with my carpenter friend and see what price id be looking at for his help. As you have done a boat load on speakers, what material would you build the cabs out of?Depends. If cost isn't an issue, I'd favour birch ply, but there's not much wrong with MDF or HDF, some even swear by good old chipboard. At least with decent birch ply, you can just stain/lacquer it to get a nice appearance. Chipboard has to be veneered or laminated, but that give good constrained layer benefits. First instinct was MDF but the ease of finishing the Birch Ply may be worth the extra nuggets. 18mm? Bigger?
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 12, 2019 22:38:04 GMT
Depends. If cost isn't an issue, I'd favour birch ply, but there's not much wrong with MDF or HDF, some even swear by good old chipboard. At least with decent birch ply, you can just stain/lacquer it to get a nice appearance. Chipboard has to be veneered or laminated, but that give good constrained layer benefits. First instinct was MDF but the ease of finishing the Birch Ply may be worth the extra nuggets. 18mm? Bigger?Is that not indicated on the drawing? Anyway, 18mm should be fine, with some judicial bracing.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 12, 2019 22:44:41 GMT
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 12, 2019 22:51:24 GMT
Haha, yes they do appeal and I bought the last speakers you advised me on which have lated longer than EVERY other component. I may do this one. Very tempting. 6.5 inches ain't no good to anyone Geoff lmao
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 12, 2019 22:59:08 GMT
Here the drawing. I can't see a thickness for the cabinet material.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 12, 2019 23:05:10 GMT
No, thickness not shown.
Those boxes are pretty deep, could be awkward. You can change the dimensions if it suits, as long as the volume stays the same and the port area and depth remain the same too.
|
|
|
Post by macca on Aug 13, 2019 6:20:52 GMT
I don't know. My pal in London has mice in his flat, that looks like the ideal solution. - Cats in the speakers.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 13, 2019 8:47:57 GMT
No, thickness not shown. Those boxes are pretty deep, could be awkward. You can change the dimensions if it suits, as long as the volume stays the same and the port area and depth remain the same too. I suppose there is an online tool that someone knows of?
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 13, 2019 8:52:54 GMT
No, thickness not shown. Those boxes are pretty deep, could be awkward. You can change the dimensions if it suits, as long as the volume stays the same and the port area and depth remain the same too. I suppose there is an online tool that someone knows of? No tool needed. just juggle the proportions about as you like. Just don't make it tall or narrow and maintain the internal volume, port area and depth. Calculations are only needed if for instance you want a smaller box or port.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 13, 2019 8:55:20 GMT
I suppose there is an online tool that someone knows of? No tool needed. just juggle the proportions about as you like. Just don't make it tall or narrow and maintain the internal volume, port area and depth. Calculations are only needed if for instance you want a smaller box or port. Christ, I'm bound to make a mess of it lol
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 13, 2019 9:16:08 GMT
No you won't. You could for instance, keep the cabinet the same as it is in dimensions and just have the driver and port on the side, making that the front. That gives you a wider box which is shallower, but still deep enough.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 13, 2019 9:54:35 GMT
No you won't. You could for instance, keep the cabinet the same as it is in dimensions and just have the driver and port on the side, making that the front. That gives you a wider box which is shallower, but still deep enough. I'm thinking: Same width but steal a bit of depth for height?
|
|
Bigman80
Grandmaster
AA Founding Member & Bigbottle Audio Creator
Posts: 16,358
|
Post by Bigman80 on Aug 13, 2019 10:33:57 GMT
No you won't. You could for instance, keep the cabinet the same as it is in dimensions and just have the driver and port on the side, making that the front. That gives you a wider box which is shallower, but still deep enough. I'm thinking: Same width but steal a bit of depth for height? I’d agree. I hate short speakers. Every speaker I’ve owned has been better raised up.
|
|
Bigman80
Grandmaster
AA Founding Member & Bigbottle Audio Creator
Posts: 16,358
|
Post by Bigman80 on Aug 13, 2019 10:36:59 GMT
Here the drawing. I can't see a thickness for the cabinet material. If you look at the “port” the internal dimensions are 50mm less than the outer walls, so the design is suggesting 25mm thick walls. If rearranging the h/w/d you will need to calculate internal volume.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 13, 2019 10:40:51 GMT
Here the drawing. I can't see a thickness for the cabinet material. If you look at the “port” the internal dimensions are 50mm less than the outer walls, so the design is suggesting 25mm thick walls. If rearranging the h/w/d you will need to calculate internal volume. Westie I may be being dense here but isn't the diagram suggesting the port should be 50x300mm? I can't see how it's suggesting that. Please explain!!
|
|
Bigman80
Grandmaster
AA Founding Member & Bigbottle Audio Creator
Posts: 16,358
|
Post by Bigman80 on Aug 13, 2019 10:47:29 GMT
I make internal dimensions 30 wide, 40.6 deep and 84.1 high.
You use the same volume with keeping 30 width, reducing depth by 50mm to 35.6 and increasing height to 95.9
I think.....
|
|
Bigman80
Grandmaster
AA Founding Member & Bigbottle Audio Creator
Posts: 16,358
|
Post by Bigman80 on Aug 13, 2019 10:52:12 GMT
If you look at the “port” the internal dimensions are 50mm less than the outer walls, so the design is suggesting 25mm thick walls. If rearranging the h/w/d you will need to calculate internal volume. Westie I may be being dense here but isn't the diagram suggesting the port should be 50x300mm? I can't see how it's suggesting that. Please explain!! Yes but it’s just an oblong hole. The sides are effectively the internal walls
|
|
Bigman80
Grandmaster
AA Founding Member & Bigbottle Audio Creator
Posts: 16,358
|
Post by Bigman80 on Aug 13, 2019 10:53:48 GMT
Look at the front-on shot. Look at the bottom where the port/hole is. It shows a port width of 300 and external walls of 350 boy names ending in n sound
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 13, 2019 11:07:36 GMT
Look at the front-on shot. Look at the bottom where the port/hole is. It shows a port width of 300 and external walls of 350 boy names ending in n soundThe front is a 50x300mm rectangle cut out of a 350mm piece of MDF/Ply. Im not seeing it. Edit.... I see what you're saying but it could be 18mm or 20mm. Nope, I get it. Well done Westie!
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 13, 2019 11:07:47 GMT
The bloke that used to do the Terminator arm and turntable, this is his final speaker rig. Looks pretty simple:
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 13, 2019 11:27:05 GMT
The bloke that used to do the Terminator arm and turntable, this is his final speaker rig. Looks pretty simple: Well he certainly doesn't care for aesthetic appeal does he lol
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 13, 2019 13:08:32 GMT
Look at the front-on shot. Look at the bottom where the port/hole is. It shows a port width of 300 and external walls of 350 boy names ending in n soundThe port could just as easily be 100mm x 150mm if it suits. It's the area and depth that matter.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 13, 2019 13:45:07 GMT
Look at the front-on shot. Look at the bottom where the port/hole is. It shows a port width of 300 and external walls of 350 boy names ending in n soundThe port could just as easily be 100mm x 150mm if it suits. It's the area and depth that matter. I'll keep them as the drawing suggests if I go ahead.
|
|
|
Post by antonio on Aug 13, 2019 13:46:31 GMT
^^^^^^^^ 75cm thick cabinet, the Doc would like that, now they would be heavy. Westie will have to do his internal volume calculations again.
|
|
|
Post by macca on Aug 13, 2019 13:56:43 GMT
If you want a proper hi-fi speaker forget single driver options. Sure they will make a pleasant enough sound but it isn't enough. Not for me anyway. if they really worked as well as the proponents suggest then everyone would be using them. One driver, no crossover, just knock up the box and you're away.
The reality is they're a massive compromise.
|
|
Bigman80
Grandmaster
AA Founding Member & Bigbottle Audio Creator
Posts: 16,358
|
Post by Bigman80 on Aug 13, 2019 14:14:17 GMT
If you want a proper hi-fi speaker forget single driver options. Sure they will make a pleasant enough sound but it isn't enough. Not for me anyway. if they really worked as well as the proponents suggest then everyone would be using them. One driver, no crossover, just knock up the box and you're away. The reality is they're a massive compromise. How much would a pair of Focals like yours be used?
|
|
|
Post by macca on Aug 13, 2019 15:06:46 GMT
I got mine cheap (£425), I think usually you're looking at around twice that.
|
|
|
Post by antonio on Aug 13, 2019 15:21:21 GMT
I thought your Focals new were about £3k, not saying you would pay that, but £425 is ridiculously cheap.
|
|
|
Post by macca on Aug 13, 2019 15:31:14 GMT
if I blow the tweeters they are £300 each to replace!
The newest version of the speakers is £5000 retail. I think they have the Berylium tweeters though. I'm slumming it with titanium.
I was lucky to get them at that price but they hung around for a while on AoS with no interest. No-one wants Focals because they're 'bright and harsh'.
|
|